Open Shop Day ....

Any and all discussions concerning events.
Post Reply
User avatar
McMahonRacing
Speed Setter
Speed Setter
Posts: 193
Joined: Tue Oct 25, 2005 9:39 am
Location: Kingston NH
Contact:

Open Shop Day ....

Post by McMahonRacing » Mon Jan 25, 2010 8:52 am

Holding an Open Shop Day w/ the FF Cobra forum members, not a huge shop more of a winter get together and a change of pace from the typical breakfast runs, if your in the area and interested swing in …….

Sunday 31st
9am til .....
334 Long Pond Rd
Danville NH 03819

Will have:

Coffee/Juice/soda/water/hot choc/ etc etc
Donuts/pastry/muffins/etc

Feel free to swing in and shoot the breeze.
Pat

User avatar
John F
Speed Racer
Speed Racer
Posts: 325
Joined: Thu Sep 06, 2007 1:56 pm
Location: Dartmouth, Ma

Re: Open Shop Day ....

Post by John F » Mon Jan 25, 2010 4:48 pm

OK, I don't have to post on the cobra forum to find out if this is still going on. See you Sunday

Maybe you can have the Rolex 24 going? I don't get speed anymore
John F
#167 SA FFR roadster

User avatar
McMahonRacing
Speed Setter
Speed Setter
Posts: 193
Joined: Tue Oct 25, 2005 9:39 am
Location: Kingston NH
Contact:

Re: Open Shop Day ....

Post by McMahonRacing » Tue Jan 26, 2010 10:19 am

Will be on in the house ..... shop only get's DVD's !!!

User avatar
breakaway500
Speed Racer
Speed Racer
Posts: 2663
Joined: Wed Aug 29, 2007 8:47 am
Location: In my shop,usually.

Re: Open Shop Day ....

Post by breakaway500 » Tue Jan 26, 2010 12:09 pm

Got heat in that shop,or am I going to wear my ski outfit? :lol: :sunny: :sunny:

What's the best way to get there off 495.. 125 to old coach rd. to mill rd. to cheney rd?
It's not what you drive, it's how you drive. "Lap times matter"

jlwhorf
Speed Racer
Speed Racer
Posts: 412
Joined: Fri Jul 08, 2005 9:38 am
Location: Atkinson NH

Re: Open Shop Day ....

Post by jlwhorf » Tue Jan 26, 2010 7:51 pm

Hey Mark, if you are driving up, you can stop by my place. It is only about 10 minutes away from Pat's and on the way.

paultg
Speed Racer
Speed Racer
Posts: 1199
Joined: Wed May 24, 2006 9:28 pm

Re: Open Shop Day ....

Post by paultg » Tue Jan 26, 2010 11:23 pm

Cool, you are only 30 mins or so from me, I might swing by.

Thanks!
Paul G.
#12

User avatar
McMahonRacing
Speed Setter
Speed Setter
Posts: 193
Joined: Tue Oct 25, 2005 9:39 am
Location: Kingston NH
Contact:

Re: Open Shop Day ....

Post by McMahonRacing » Wed Jan 27, 2010 3:02 pm

Will be 60f min, can turn it up if you need :) !!!!

There are a couple ways .. from Rutland I usually run down Rt 2- Rt 495 N - Rt 125 N or you can run Rt 93 N too Rt 111 E ... not much time difference, just more traffic on Rt 125 !!!!!

There is also a senic route, following Rt 111 to Amherst Flea Market, down to Hollis but I have to do that by braille :) !!!!

Everyone is welcome so swing on in :) !!!!

User avatar
breakaway500
Speed Racer
Speed Racer
Posts: 2663
Joined: Wed Aug 29, 2007 8:47 am
Location: In my shop,usually.

Re: Open Shop Day ....

Post by breakaway500 » Wed Jan 27, 2010 5:19 pm

Sunday a.m. traffic should not be bad on 495..I'll probably do the 125 etc route.. I may take a side trip up to Kittery first as I have not been in a while and I don't get out of my cave very often... :shock: (running low on ammo...) Hey, need some wood for the fireplace? :wink:
It's not what you drive, it's how you drive. "Lap times matter"

User avatar
McMahonRacing
Speed Setter
Speed Setter
Posts: 193
Joined: Tue Oct 25, 2005 9:39 am
Location: Kingston NH
Contact:

Re: Open Shop Day ....

Post by McMahonRacing » Fri Jan 29, 2010 12:27 pm

If you run to Kittery first ..... consider Rt 101 E or Rt 107 E off Rt 95 S over too Rt 125 ..... we typically cut over on Rt 107 on the way back from Caribou .... Pat

User avatar
breakaway500
Speed Racer
Speed Racer
Posts: 2663
Joined: Wed Aug 29, 2007 8:47 am
Location: In my shop,usually.

Re: Open Shop Day ....

Post by breakaway500 » Fri Jan 29, 2010 2:27 pm

Thanks,Pat. C-U Sundaaaaaaaaaaay! :wink:
It's not what you drive, it's how you drive. "Lap times matter"

User avatar
McMahonRacing
Speed Setter
Speed Setter
Posts: 193
Joined: Tue Oct 25, 2005 9:39 am
Location: Kingston NH
Contact:

Re: Open Shop Day ....

Post by McMahonRacing » Sun Jan 31, 2010 6:28 pm

Guys .... Just wanted to pass along a quick Thanks for visiting today ...... enjoyed it ...... Thans Again ... Pat

User avatar
breakaway500
Speed Racer
Speed Racer
Posts: 2663
Joined: Wed Aug 29, 2007 8:47 am
Location: In my shop,usually.

Re: Open Shop Day ....

Post by breakaway500 » Sun Jan 31, 2010 8:57 pm

Had a great time as well,and thanks for the TIG welder! That was a wonderful door prize.. :wink:
It's not what you drive, it's how you drive. "Lap times matter"

User avatar
John F
Speed Racer
Speed Racer
Posts: 325
Joined: Thu Sep 06, 2007 1:56 pm
Location: Dartmouth, Ma

Re: Open Shop Day ....

Post by John F » Sun Jan 31, 2010 10:16 pm

breakaway500 wrote:Had a great time as well,and thanks for the TIG welder! That was a wonderful door prize.. :wink:
Who took my V710's?
John F
#167 SA FFR roadster

Post Reply

Who is online

Users browsing this forum: Bing [Bot] and 1 guest