Parts for sale: Fikse & Kosei wheels, misc parts

[Mick]

Fikse FM10's 17x8.5 ET38 - SOLD

Kosei K1's with Hoosier R6 SOLD

Kosei K1's with Hoosier Wets SOLD

Wilwood B Compound Pads - $80 - (6x6x6" 4.6 lbs)
These fit Wilwood SL6R calipers. The pads are Wilwood part number 15B-5939K. These were $140 new. Used for 4-5 laps, essentially new. Wilwood lists these as being 20mm including the backing plate.






Auto Meter High Pressure Isolator - $50 (6x6x6" 0.5 lbs)
Lightly used, was test fit only.

[StephanAlfa]

They look lovely Mick but I afraid I cannot use them because it will bump me off SSB class

[Mick]

use them for the street and put track rubber on your stock wheels

[savage217]

Fikse fm10's are one of the nicest wheels made. An all time favorite. Good luck with sale.

[TroyV]

Those Fikses would look awesome on my 328. I just can't see putting 1800 dollar wheels on a 400 dollar car.

I have seen these wheels in person. They are very light..and very nice aside from the minor blemishes Mick mentions.

[Mick]

Price on the Fikses reduced from $1800 to $1700

[Mick]

Added brake pads and high pressure isolator to the listing

[Mick]

Price on the Fikses reduced to $1600

[Mick]

Price on the Fiskes reduced to $1500

[Mick]

Tires are dismounted from the Fikses. I measured the rims and as it turns out they are 17x8.5"
I want these gone. Make an offer.

[savage217]

Tires are dismounted from the Fiskes. I measured the rims and as it turns out they are 17x8.5"
I want these gone. Make an offer.

Mick, is that from lip to lip or just the barrel? Sometimes people do not measure properly and end up measuring lip to lip rather than the proper barrel method. I will spread the word to some friends about these wheels, they look super clean. Have you tried bimmerforums? You can sell anything on that site.

[Mick]

Measured from the insides of the lips, which is what I was told was the proper method by Scott at Fastrack, and what I've read on the web. Are you saying the measurement is supposed to be from the outsides of the barrel?
inside of the lips = 8.5"
outsides of the barrel = 9.5"

Did post them on Bimmerforums, got a few bites but all turned out to be deadbeats.
http://forums.bimmerforums.com/forum/sh ... ?t=1843749

Thanks for asking around.

[Mick]

Now that the tires are off I was able to accurately measure the offset which is ET38.
So these are 17x8.5 ET38

Here are more pics.
http://lh3.googleusercontent.com/-NVPzG ... 001134.jpg
http://lh5.googleusercontent.com/-UKFg3 ... 001123.jpg
http://lh4.googleusercontent.com/-rS99Q ... 001124.jpg
http://lh5.googleusercontent.com/-Ug3X4 ... 001125.jpg
http://lh6.googleusercontent.com/-1kQtS ... 001127.jpg
http://lh5.googleusercontent.com/-GJS-a ... 001131.jpg
http://lh6.googleusercontent.com/-_gxDg ... 001133.jpg

Center caps will be included, I just had them off when shooting these pics.

[dradernh]

If necessary, you can call Fikse with the serial numbers to get all the data associated with each wheel

[Mick]

Bump. Fikses still available, price dropped to $1100. Going on Ebay soon.